Gevurah Sukkah - National Sukkah Outlet

on behalf of national sukkah outlet we would like to thank you for purchasing it is our hope that your new sukkah will give you many years of pleasure and enjoyment over the next few minutes you will watch a detailed video outlining the necessary steps to build the guru we advise that you watch the complete video before starting to construct your support parts let's begin by identifying the parts that come along with the guru there are full-size panels short panels window panels a door corner posts wall supports supports and assorted brackets ww tt ss or slider uu or s bracket and xx brackets the following table details the quantity of each part that has come with your set please keep in mind that custom sukkahs will have different number of parts before beginning to build your circle please check that you have all the necessary parts key to building in order to build the sukkah smoothly and easily it is important to keep in mind two key points the inner side of each panel is smooth while the side of the panel that faces outward has cross braces each panel also has a male and female side the male side juts out and will always be on the right side when you look at the panel from the outside the female side is indented with a ridge and will always be on the left side of the panel when you look at it from the outside keeping this in mind will make the building process quick and easy once you've identified all your panels it is advisable to lay them out or lean them on a wall in the layout that you prefer selecting the placement of the door and windows according to your needs let's build one now that all the panels have been laid out begin building one corner by inserting a full corner post's female side into a panel's male connector rotate the corner post clockwise so that the corner post snaps in it's important to make sure that the corner post is completely connected from top to bottom to the panel now you will construct the adjoining corner by inserting the female side of the panel into the male connector of the corner post rotate the panel clockwise so that the panel snaps in you will now have an l-shaped corner although it can stand by itself we recommend supporting it until the sukkah is complete to prevent damages two now insert bracket ww on the bottom of the panel with the groove facing the exterior of the sucker you are now ready to connect the next panel once again match up the male and female connectors holding the panel above the ww bracket once you've moved the panel clockwise you can slide it down to fit into the ww bracket three place a slider over every two connecting panels as shown four you'll repeat these steps to continue building the sukup once you have a complete wall place a full corner post at the end of the final panel and continue building the next wall five once you've assembled the third complete wall go back to finish the final side in the opposite direction turning counterclockwise until you've completed the fourth wall six when all four walls are complete insert a half corner post over the corner of the sukkah and slide it down by placing the female side of the corner post over the male side of the last panel and the male side of the corner post over the adjacent female side of the sukkah slide the corner post to the bottom and repeat this step with the second half corner post if you're having difficulties with this step check that the two sukha walls are forming a square shape and try using wd-40 or similar lubricant to help slide down the corner posts seven upon completing the walls of the sukkah place the uu brackets over the top of the sukkah where each two panels meet make sure that the notch of the bracket is facing outward eight now place tt brackets in the same manner near the end of each wall nine once all the brackets have been placed lay the two by three wooden supports inside the tt and uu brackets with the wide side facing down your sukkah can now stand independently 10. place the xx brackets over the tops of the longer walls directly facing each other they should be evenly spaced on each side then insert the sock support beams and turn the knobs to hold the beam tight if necessary you should adjust the beams to be evenly spaced in order to properly support the weight of the shock 11. now roll out your and enjoy your sukkah notes 1. placing a sukkah on an uneven surface may cause it to be shaky or might cause damage to the sukkah if your surface is uneven try tying your sukkah to a permanent object 2. always make sure that the sukkah is completely dry before disassembling and storing it to disassemble the sukkah simply follow these directions in reverse remember to have another person support a corner of the sukkah once this assembly has begun three when storing and handling your sukup make sure that the panels never rest on the male connector as it may get damaged rendering the panel unusable 4. panels can be stacked one atop another for storage do not place any other object on top of the sukkah once again on behalf of national sukkah outlet we would like to thank you for purchasing a gevora sukha it is our hope that your new sukkah will give you many years of pleasure and enjoyment please note in situations of inclement weather or strong winds we strongly suggest that your sukkah be taken down or reinforced appropriately you